ROM Knee Brace

Knee brace for ACL knee reconstruction,
meniscus repair & fracture of knee / Patella fracture

Prefabricated. Custom adjusted range of motion (ROM) Knee Brace controls and restrict flexion / extension of the knee joint through a multi point joint fixation system to allow a range of motion or immobilization to the knee. Universal design allows it to be used on quite a big range of population and for a multiple orthopedic problems associated with knee joint in specific and the lower limb in general.


ROM Knee Brace - Features

	Range of motion 0-135° flexion and 0-75° hyper extention with an interval of 7.5°

	Ensure immobilization at any angle motion between any two angles.

	Universally acceptable fix lock with easy pin insertion.

	Pin locking with transparent disk for safety.

	Convenient design, easy to apply in the least time.

	Special bonded fabric for lining which has high cushioning coefficient, provides a good grip of the product to the leg.

	Universal design, one size fits all.

Size

Universal - One size fits all (380mm to 575mm of thigh size)


Disease Matrix

	Prevention of sports injury

	Resistant patello femoral pain

	Patella / Joint dislocation

	Post operative knee immobilization

	Post cast removal following fracture

	ACL knee

	PCL ruptures / injury / surgery

	Post knee replacement rehabilitation

Buy Online

Size Code Cost (USD)

Universal

D-10

$ 44

Construction

ROM Knee brace comprises of the fabric wrap for the calf and the thigh, they are made out of a three layered bonded fabric. ROM hinges contain multipoint fixation graduated disc (MPFGD) in the centre connected to light weight rigid bars on both sides. The (MPFGD) can be adjusted to any angle of flexion or hyper extension to ensure fixation of knee joint at any angle or a controlled motion between any two angles. Angle between two adjacent pins is 7.5*.

Technical Parameters		Benefits
	Two pieces wrapping system		Easy application and removable secure and tight holding of the brace to the leg
	Aluminum hinge bars		Light weight , no rusting and long life
	Steel MPFGD		Bears the load of the leg without deformation, no play of the hinges even after prolong use
	Separate pins for extension and flexion adjustments		Knee joint can be fixed at any flexion angle controlled motion between any two chosen flexion angles
	Transparent disc to cover MPFGD pins		No accidental removal of the pins, clear visibility of holes pin and the angles of knee adjustment
	World class workmanship		Improves aesthetics, improves patient compliance, improves life, improves comfort
	Clean manufacturing environment		Low bio-burden, dust free, hypoallergenic

Application		Instructions

	Prevents the knee joint from unexpected load, motion to stimulate healing and provides knee support.		Use this product under strict guidance of a qualified doctor
	Postoperative treatment and rehabilitation		If pain increases or persists, discontinue use and consult your physician
	Posttraumatic treatment and rehabilitation		Discontinue use in case of allergy rash or itching
	Provide stability to the weak / injured knee joint.		Adjust strapping for secure and comfortable fitting
	To prevent an excessive range of knee joint motion		Follow instructions mentioned on the box carefully
	To decrease limitations in maintaining a standing position or in walking short distances		Keep out of reach of children

How to use

Affix the hinges on the two sides of the knee joint with the Velcro on the inner side of the hinge, so that the centre of the MPFGD coincides with axis of the knee. Take care that both the hinges are upright as per the arrow mark and the bending is in line with knee bending.

Wrap the Velcro bands around the leg one by one carefully passing them through the slots in the PP buckle strip on the hinge.

Fasten the Velcro strips with the reverse buckling to a comfortable, secure grip.

Movements

If immobilization required at a particular angle then move both, flexion as well as hyperextension pins to holes corresponding to degree of flexion required.

If flexion movement is required between two angles then move the flexion pin to the hole corresponding to higher degree angle and the extension pin to the hole corresponding to lower degree.

If no flexion bending or movement is required then both the pins be affixed at 0 position

For free flexion movement of the leg place flexion pin at 120 degree and extension pin at 0 degree

We have more knee braces

ROM Knee Brace

Knee brace for ACL knee reconstruction, meniscus repair & fracture of knee / Patella fracture

Knee brace for ACL knee reconstruction,
meniscus repair & fracture of knee / Patella fracture